Monday, February 28, 2011

How to Reset Canon Pixma iP4000 Printer

If your Canon Pixma iP4000 printer users, please read this post, hopefully can help

Here's how to reset Canon Pixma iP4000 Printer
  1. Position the printer off, press and hold the "Resume / Cancel", then press and hold the "Power / Power". Keys should not be removed once served until LED light turns green.
  2. While still holding down "Power / Power", release the button Resume / Cancel ".
  3. Then, the position of the Power button still held / pressed, press the "Resume / Cancel" 2 times, then release both buttons.
  4. When the LED light turns green, press the "Resume / Cancel" button 4 times.
  5. Then press the button "Power". LED light will glow green, and wait a printer will reset.
  6. When finished, the printer back to the menu selection mode automatically
  7. Finally press the "Power / Power" to exit service mode.
Good luck ..............

How to Reset Waste Ink Counter On Epson RX500

The following post is about how to reset waste ink counter on Epson RX500. If you need it, please just read and hopefully help ........

Here are the steps to Wast Ink Counter Reset On Epson RX500
  1. Press and hold all of the following keys: Power / Power, Load / Eject, Stop, B & W, Color.
  2. Release all buttons.
  3. Once the printer is on, you'll see "Init eeprom" on printer screen.
  4. Press the Color button to clear the counter / reset.
  5. Completed
Good luck .......

Friday, February 25, 2011

Canon MP258 Error Code and how to fix it

Here I get a link on the Canon MP258 error code explanation. Please read and hopefully useful ....

Canon MP258 Error code and fix:

MP258 Error code there are 2 types of codes, namely:
1. that uses the letters before P, for example P07
2. that uses the letters before E, eg E05

P Canon MP258 Error code:

P02 (Carriage error)

Solution:
1. Make sure no foreign object stuck in the roll printer.
2. Clean and check the encoder, may be exposed to splashes of ink.

Wednesday, February 9, 2011

How to Repair Harddisk Bad Sector with Low Level Format


This time I will share the experience when the computer once I am slow in running the program, often hangs and suddenly can not get into Windows / always fail to boot. After I check one by one the hardware was there on the hard drive problem, when the check hard drive using another computer that there was Bad Sector in HDD is 4 Kb. Well, for those of you who have a hard drive with a case similar to the hard drive I am, here is the solution that has proven itself I am quite satisfied with the results ....


Monday, February 7, 2011

How to Fix the Printer Canon iP 2770 Orange Led Blinking 13 Times

Discussion this time on the blink 13 times Orange on Canon iP2770 Led indicator. This incident may be quite confusing for those who have never experienced it. OK just ...

Indications:
When the printer is turned on seems OK, but after the printer is commanded to print, Led indicator light flashes 13 times Orange Canon iP2770 on this. Here's a picture that appears on the screen:


How To Reset Printer Canon MP258

This post I will discuss on How to Reset Canon MP 258 printer which I've always prove successful. Because a lot of Friends who seek this MP258 resetter software. So let's just ..........
 



How to Solve Problems Catridge Not Detected and Slow Back To place on Epson TX111 Printer

If you are a user This TX111 Multifunction Printer Epson Catridge problems are not detected and Catridge slowly back into place, do not be confused. Please try the tips in this post I have time, maybe can help .......



How to Upgrade Version 1.1 Linksys WRT54GL

This post about how to upgrade Access Point Linksys WRT54GL Version 1.1 to the dd-wrt Generic Version 24 Standard, because the firmware Linksys WRT54GL feels less full power, the following tutorial I will share how the steps to upgrade its firmware ....

Immediately, the Linksys WRT54GL firmware upgrade process is very easy, but you previously used to prepare all the necessary equipment or devices, such as Linksys AP itself and download the software upgrade, following the previous steps but you need to know to upgrade the Linksys WRT54GL to dd-wrt v24 standard generic first you must upgrade to the dd-wrt v24 generic mini (important), well to step let us read together ....


How to Unlock Modem ZTE MF622

This time I will post how to unlock ZTE MF622 modem, hopefully I'm posting useful. Immediately, easy way, and here I provide a free unlock software without having to pay because it was the same crack hackers out there. Here are the steps:



How to Reset MP145 Printer Error 27 (E27)

There was someone who sent the message via email to me and asking how to reset error 27 (E27) on the Canon MP145 printer, his intention I will reply to e-mail but when I reply, e-mail reply from I was not sent and an error occurs like this "Delivery to the Following recipient failed permanently." Maybe you were wrong to enter your e-mail. Okay, for you who had sent messages via e-mail because I could not reply, I'll post here just hopefully you can have time to read it and try practiced on your Canon MP145 Printer.